EPSON9800 10600故障报错代码查询

EPSON9800 10600故障报错代码查询EPSON9800..10600报错代码(报错全集)0100 废墨垫寿命少（少于1%）00000100 废墨垫寿命到，必须更换00000101 墨管寿命到00010000 PF马达Encoder报错00010001 PF马达步进错误00010002 PF马达过载00010003 PF马达延时错误00010004 CR马达Encoder报错00010005 CR马达步进错误00010006 CR马达过载00010007 CR马达延时错误00010008 马达控制延时错误00010009 离合器控制延时错误0001000A CR初试位置传感器错误0001000C PG初试位置传感器错误0001000D Cover传感器报错（右侧）0001000E Cover传感器报错（左侧）0001000F CR马达控制错误00010010 PF马达控制错误00020000 NVRAM 错误00020001 初始化RAM错误00020002 SRAM报错00020003 DRAM报错10000004 CPU 报错10000006 CPU 报错10000009 CPU 报错1000000A CPU 报错1000000B CPU 报错100000 CPU 报错 　　 全新整理ＥＰＳＯＮ报错全集（珍藏版）：　0100 废墨垫寿命少（少于1%）00000100 废墨垫寿命到，必须更换00000101 CR（光栅）马达到达了寿命00010000 PF（进纸）编码器检查错误00010001 PF 马达是在步进错误00010002 PF马达过载00010003 PF马达延时错误00010004 CR 编码器检查错误00010005 CR马达步进错误00010007 CR马达延时错误00010008 马达控制延时错误00010009 离合器控制延时错误0001000A CR初试位置传感器错误0001000C PG初试位置传感器错误00010014 加压失败0001001B 打印头温度错误（检查头缆线的位置和接触）0001001D CR传感器报错（右侧）0001001E PF传感器报错（左侧）00010020 CSIC reading/writing 错误（检查CSIC板的接触）00010023 RTC 分析错误00010026 RTC 通信错误00010027 压力泵浦微空气泄漏错误00010028 打印头错误0001002A CR ASIC ECU 错误0001002D 清洁单位到达了它寿命00010035 清洁泵侦查错误00010036 类型B 委员会设施错误p.19600010037 顶头热敏电阻错误（检查头缆线位置和接触，以及打印头是否匹配）00010038 支晶体管热敏电阻错误0001003E 压力传感器失败0001003F 压力马达到达了它的什么寿命00010040 打印的位置误差00020000 NVRAM 错误00020002 SDRAM 错误00020003 起动节目总和错误0002000A 程序装载错误0002000B 内存是不足的0Dxxxxxx 一个误差编码为调试RTC 定时器的0Exxxxxx A time-lag 100000E0 CPU 地址错误(装载) 10000100 个CPU 地址错误10000180 个CPU 后备的指令编码例外错100001A0 CPU 槽孔未定义命令例外错误100001.C0 交流电能被关闭100005C0 CPU DMA 地址错误10000xxx CPU 错误0001000F CR马达控制错误00010010 PF马达控制错误00020000 NVRAM 错误00020001 初始化RAM错误00020002 SRAM报错00020003 DRAM报错10000004 CPU 报错10000006 CPU 报错10000009 CPU 报错1000000A CPU 报错1000000B CPU 报错100000 CPU 报错 00000101 The CR Motor reached its end of life. p.18600010000 PF Encoder check error p.18700010001 The PF Motor is out of step. p.18800010002 Overcurrent occurred on the PF Motor. p.18800010003 The PF Motor out of position time-out error p.18900010004 CR Encoder check error p.18900010005 CR Motor is out of step. p.19000010007 The CR Motor out of position time-out error p.19000010008 Servo interrupt watchdog time-out error p.19100010009 System interrupt watchdog time-out error p.1910001000A Carriage home position detection error p.1910001000C PG home position detection error p.19200010014 Failure of pressurizing p.1920001001B Head driver (TG) temperature error p.1930001001D CR servo parameter error p.1930001001E PF servo parameter error p.19400010020 CSIC reading/writing error p.19400010023 RTC analyzing error p.19400010026 RTC communication error p.19500010027 Pressure pump micro air-leak error p.19500010028 Head error p.1950001002A CR ASIC ECU error p.1950001002D The Cleaning Unit reached its end of life. p.19500010035 Pump phase detection error p.19600010036 Type-B board installation error p.19600010037 Head thermistor error p.19600010038 Transistor thermistor error p.1960001003E Pressure Senso* **ilure p.1960001003F The Pressure Motor reached its end of life. p.19700010040 Printing position error p.19700020000 NVRAM error p.19700020002 SDRAM error p.19700020003 Boot program sum error p.1980002000A Program load error p.1980002000B The internal memory is insufficient. p.1980Dxxxxxx An error code for debugging p.1980Exxxxxx A time-lag of the RTC timer p.199100000E0 CPU address error (load) p.19910000100 CPU address error (store) p.19910000180 CPU reserved command code exception error p.199100001A0 CPU slot undefined command exception error p.200100001C0 The AC power is shut off. p.200100005C0 CPU DMA address error p.20010000xxx CPU error p.200首先是一些7600/9600上机器错误代码的分析!!!7600/9600 Field Repair Guide00000101 CR motor life字车电机寿命00010000 PF motor encoder check error马达直流电机传感器错误00010001 PF motor out of step马达直流电机00010002 PF motor overcurrent00010003 PF motor in-position time-out00010004 CR motor encoder check error00010005 CR motor out of step00010006 CR motor overcurrent00010007 CR motor in-position time-out00010008 Servo interrupt watchdog time-out00010009 System interrupt watchdog time-out0001000A CR home position sensor error0001000B PF home position sensor error0001000C Head slide (PG) home podition sensor error0001000F CR motor PWM output faulty00010010 PF motor PWM output faulty0001001B Head driver(TG) temperature error0001001D CR servo parameter error0001001E PF servo parameter error00010020 CSIC reed/right error00010022 Ink type error(setting on printer body side)00010023 RTC analysis error00010025 CSIC communication error00010028 HEAD error00010029 Unidentified NMI0001002A CR ASIC ECU error0001002B PF ASIC ECU error00020000 NVRAM error00020002 SDRAM error00020003 BOOT program SUM error00020009 Flash memory SUM error0002000A Program load error0002000B Internal memory shortage error0002000C Review error100000E0 CPU address error (load misalignment)10000100 CPU address error (storage misalignment)10000180 CPU reserve command code exception error100001A0 CPU slot illegal command exception error100005C0 CPU DMA address error10000xxx CPU error7800/9800错误代码分析//------------------------Printer Status(打印机状态)------------------------//00010000=打印机状态00010001=墨水存量(%)00010002=切纸器寿命(%) 00010003=介质对切纸器的寿命有很大的影响。00010100=零、配件寿命信息00010103=开始 Media Counter Settings00010104=正在捕获状态...00010105=无法与所选择的打印机进行通信。00010006=墨量低00010007=维护箱几乎已满00010008=维护箱请求00010009=纸张存量低00010010=重大错误00010011=打印其他 I/F 数据00010012=前盖开启00010013=解除打印纸调节杆00010014=卡纸00010015=缺墨00010016=缺纸00010017=设定面板00010018=打印纸通道发生错误00010019=单页纸尺寸错误00010020=单页纸出纸错误 00010021=维护箱已满00010022=纸张剪切错误00010024=清洁错误（厚纸）00010025=纸张错误00010026=纸张歪斜错误00010027=抬起墨舱杠杆锁00010028=没有维护箱00010029=命令错误00010030=后盖开启00010031=多传感器捕获错误00010032=自动调整错误00010033=清洁错误00010034=通信错误00010035=墨盒错误00010036=不正确的墨盒00010051=维护箱 (%)00010052=卷纸(m)00010053=卷纸(ft)00010054=单页纸(页)00010059=单页纸00010060=顶盖开启00010061=完成打印00010062=打印就绪00010063=关闭记数00010064=正在打印00010065=未准备好打印00010066=墨水干燥00010067=检查打印头00010068=调整纸张位置//------------------------ Parts Life(零件寿命)------------------------//00020000=零、配件寿命00020001=字车电机寿命 (%)00020002=走纸电机寿命 (%)00020003=清洁部件寿命 (%)00020004=电机寿命 (%)00020100=关闭00020102=维护箱信息//------------------------ Maintenance Information(维修信息)------------------------//00030001=编号：00030003=日期和时间//------------------------ Column Settings(行设置)------------------------//00050000=设定栏00050100=<<新增00050101=删除>>00050102=上移00050103=下移00050104=确定00050105=取消00050001=作业名称00050002=用户名称00050003=主机名称00050004=已使用 I/F 00050005=作业状态00050006=介质 ID00050007=使用的墨水 (MK)00050008=使用的墨水 (C)00050009=使用的墨水 (M)00050010=使用的墨水 (Y)00050011=使用的墨水 (LK)00050012=使用的墨水 (LC)00050013=使用的墨水 (LM)00050014=使用的墨水 (LLK)00050015=使用的墨水 (MK2)00050016=使用的墨水 (C2)00050017=使用的墨水 (M2)00050018=使用的墨水 (Y2)00050019=使用的墨水 (PK/MK)00050020=使用的纸张00050021=打印开始时间00050022=打印完成时间00050023=打印时间00050025=墨盒信息00050026=打印头运动次数00050027=页00050028=介质消耗区域00050029=标准转换尺寸00050030=双面打印00050031=显示项目00050032=隐藏项目00050033=已使用的墨水//------------------------ Job Infomation(作业信息)------------------------//00040000=作业信息00040200=文件00040201=保存为CSV文件格式00040202=删除日志文件00040203=升级作业信息00040205=浏览00040206=部件00040207=米00040208=英尺00040209=设定栏...00040730=并行00040731=USB00040732=选项 I/F 100040733=选项 I/F 200040734=IEEE139400040735=未使用00040737=未决的00040738=完成00040740=中止00040741=送纸器00040742=手动送纸00040743=卷纸00040744=超 B000040745=B000040746=B100040747=B200040748=B300040749=B400040750=B500040751=超 A000040752=A000040753=超 A100040754=A100040755=A200040756=超 A300040757=A300040758=A400040759=信函纸00040760=US B00040761=US C00040762=US D00040763=US E00040764=无数据00040765=未知00040766=8 色 - 照片黑00040767=8 色 - 粗面黑00040768=4 色00040769=开启00040770=关闭00040771=毫米00040772=英寸00040774=无标题的//------------------------ Wizard(1)(向导1)------------------------//00060000=Printer Watcher 安装向导00060001=您想要在启动计算机时就启动此应用程序吗？00060002=监控设定00060100=启动计算机时就启动此应用程序00060101=启动计算机时不启动此应用程序00060103=下一步//------------------------ Wizard(2)(向导2)------------------------//00070001=选择您想要的功能。00070003=功能选择00070500=获取作业信息日志00070501=监控打印机状态00070002=打印机警报和错误通知方法00070502=显示打印机状态窗口00070503=打开警报铃声00070101=上一步//------------------------ Wizard(3)(向导3)------------------------//00080001=选择要监控的打印机。00080007=被监控的打印机00080002=正在确认...00080003=(无法通信)00080005=打印机选择列表00080006=若监控打印机时在选配器中转换被监控的打印机，则打印机不能正常工作。//------------------------ Wizard(4)(向导4)------------------------//00090001=根据下面的设定监控打印机。\n请确认。00090101=完成00090006=无//------------------------ Always Start-----------------------//-00100200=显示打印机信息00100201=显示作业日志00100202=设定...00100203=版本信息00100204=退出00100205=退出00100001=启动 Printer Watcher...00100206=帮助00100207=关于 Printer Watcher...00100209=编辑//------------------------ Warning(警告)------------------------//00120301=没有足够的内存空间运行此应用程序。00120302=无法找到所需的打印机驱动程序。请安装所需的打印机驱动程序。00120303=无法找到 EPSON Status Monitor 3。请安装 EPSON Status Monitor 3。00120304=您想停止监控打印机吗？00120305=无法找到帮助文件。00120306=要更改打印机的监控设定，请关闭打印机状态窗口和作业信息窗口。00120307=将删除所有打印机(%s)的作业日志。您要继续吗？00120308=不能输出 CSV 文件。00120309=要求拥有管理者权限。请以管理者身份登录，然后执行安装。00120310=请选择一个或更多要监控的打印机。00120311=打印机的需求信息。00120312=不能读取打印作业日志文件。00120313=应用程序无法在此操作系统下运行。请检查您的系统环境。00120314=可能已删除要监控的打印机的驱动程序。请再次确认设置。00120315=打印机监控设定不正确。您要退出吗？00120316=没有要监控的打印机。打印机监控程序将停止运行。00120317=被监控的打印机已经改变，因为打印机在选配器中已改变。00120318=无法正确操作。因为不支持在选配器中所选择的打印机。请重新设定。00120319=在扩展文件夹中的CarbonLib库文件是旧的版本，所以一些功能不能使用